Sanitary Stainless steel Clamped 3-PCS Ball Valves
Can be applied in food, beverage, brewing, dairy, water treatment, pharmaceutical and chemical industries, with an intended purpose of controlling the flow of fluids with viscous or particulate matters in pipelines or pressure vessels.
Processed by state-of-the-art equipment in workshops. Best service is provided.
Inspected by a professional quality control team. Best quality is guaranteed.
With experiences accumulated through years and deep talks conducted between end users of fluid pipelines, we are able to continuously optimize the design and structure of ball valves.
Blow-out proof stem adds safety and reliability to the full extent.
Thickened stem packing; V-shaped stacking design; Adjustable self-compensating gland.
Multiple control modes. Easy to realize remote or automatic control.
All sealing materials contacting with fluids are reinforced PTFE, in accordance with FDA177.1550 and GMP standards.
Support CIP (Clean-In-Place) and SIP (Sterilization-In-Place).
Material
Valve bodies and caps are delicately cast by CF8, CF3M or 2205 materials; or forged by F316L. In case of specific working conditions, special materials, such as HC/Ti, will also be applied.
Seal Material
PTFE seals are compatible with most operating conditions (-10ºC~+110ºC).
TFM600 seal is also available as an option, which is also compatible with many operating conditions (-60ºC~+150ºC).
POB seal is also available for high-temperature operating conditions (-10ºC~+210ºC).
In the range of its specified working pressures and temperatures, the valve is perfectly sealed. When pressure increases, the sealing performance can automatically be improved. Due to a small friction between seals and valve body, the stem torque is also relatively small.
Our sanitary ball valves are fully sealed in two directions, which comes as standard. The sealing structure can fill the clearance in the cavity, ensuring no media is detained in the cavity, and the cavity and tube can thus be cleaned.
But for front-end or rear-end discharge use, it is more economic and practical to apply half sealed valves.
Flexible 3-PCS Design
3-PCS ball valves are flexible to set up and easy to be maintained online or offline, which significantly minimizes the production downtime due to valve or pipeline maintenance. During maintenance, it is not necessary to disassemble the actuator or joint component from the valve. When the maintenance is completed, it is also convenient to re-amount the valve or actuator components; no calibration is needed.
Integral Mounting Surface
Integral mounting surface conforms with ISO 5211 standards and assists the correct installation of actuator, ensuring the actuator is not able to move when rotating at high speed or loading for a long time. When the valve is working at its highest allowable working pressure, the actuator can still be safely and conveniently removed and maintained.
Surface Roughness
Sanitary ball valves are processed through fine CNC machining. All fluid-contacting surfaces are delicately polished to meet the standards that the internal surface roughness shall meet Ra≤0.8 μm. Or we can meet Ra ≤ 0.4 μm or even Ra ≤0.25 μm according to your requirements. Though, the above standards don't apply for the external surfaces of forged products. The external surface roughness can meet Ra≤0.8 μm or Ra ≤ 0.4 μm.
Strict Assembly Procedure
To prevent contamination, all components, after processing, shall be put in an ultrasonic cleaning sink and cleaned with special solutions to remove oil and grease. Assembly and calibration shall be carried out in a designated cleaning room, so as to make sure that every ball valve can be used in a sanitary system.
Technical Parameters: |
Actuation |
stem, auto-reset stem, turbine, aluminum pneumatic actuator (single/double acting), electric actuator |
Size |
DN10-DN100 1/2"-4" |
Body |
one-channel body, tank bottom type body, V-shaped regulating body |
Fluid-Contacting Surface |
ASTM A351:CF8/ CF3M/2205 (304/316L/2205) |
Non-Fluid-Contacting Surface |
ASTM SS304/CF8 |
Connection |
Welded, Clamped, Flange, Female Thread, etc. |
Operation Pressure |
PN16bar |
Operation Temperature |
Dependent on seal materials |
Seal Material |
Ambient Temperature (10~+110ºC): PTFE seal |
|
Medium Temperature (-60~+150ºC): TFM1600 seal |
|
High temperature (10~+210ºC): POB seal |
Fluid-contacting surface roughness: Ra≤0.8μm Ra≤0.4μm Ra≤0.25μm |
Optional Accessory (Pneumatic) |
Handwheel Clutch (Only available for aluminum pneumatic actuators) |
Optional Accessory (Transponder) |
APL210N: IP67 2-NPT1/2" |
|
VLS1000: Exd IIBT6 Explosion-proof IP67 2-NPT3/4" |
|
VLS1000S: ExdIICT6 Explosion-proof IP67 2-NPT3/4" |
|
VLS1121: ExiaIICT6 intrinsically safe explosion-proof IP67 2-NPT3/4" |
|
VLS1221: ExiaIICT6 with P&F IP67 DC 8V intrinsically safe explosion-proof 2-NPT3/4" |
Optional Accessory (Solenoid Valve) |
Solenoid valve + air filter pressure-relief valve (plastic connector +PU air pipe) AC220V AC110V AC380 |
|
Explosion-proof solenoid valve + air filter pressure-relief valve (pipe ferrule + stainless steel air pipe) DC12V DC24V |
|
ASCO Explosion-proof solenoid valve + air filter pressure-relief valve (pipe ferrule + stainless steel air pipe) DC12V DC24V |
Optional Accessory: NM500 Intelligent Positioner: set input signal at 4-20mA and output signal at 4-20mA DC 24V |
Application:
This type of ball valve series is a kind of sanitary valve which used to control the material transfer.It is widely used in food,beverage processing,pharmaceutical and chemical industry area.
Working Principle:
With the 90° rotary handle,drive the precise manufacturing ball body which with through cavity,turn on or off,so that can control the medium flow.
Products features:
1.Valve stem anti-flying design
2.The connection between valve body and bonnet with positioning stage design.
3.Circulation
4.No retention design
5.ISO 5211 Mounting Pad
6.360°Installation
7.Valve stem anti-flying design
Product Name: |
Sanitary Stainless steel Clamped 3-PCS Ball Valves |
Valve Body Material: |
SS304 or SS316L |
Seal Material: |
PTFE |
Max. Working Pressure: |
0~10Bar |
Max. Working Temperature: |
120 degree C |
Availably size: |
DN10-DN100 or 1/2" - 4" |
Availably connection: |
Thread,Weld,Clamp,Flange |
Surface |
finishing: Internal surface Ra0.6μ M, external surface |
Gaskets: |
PTFE(FDA 177.1550) |
Availably standard: |
DIN,SMS,3A,ISO |
Operated: |
Manual,Pneumatic,Electric |
Certificate: |
3A, FDA |
DELIVERY:
Usually within 15days after receiving T/T down payment
PAYMENT:
We prefer to do T/T or LC.
FAQ:
I. Are you factory?
Yes,we are factory and we're specilized in manufacturing Valve and fittings for 15 years.
II. Which countries do you expot to?
We're exporting to about 40 countries around the world. For Europe and America Area ,it takes about 30%,Middle East area:40%, Africa area:30%.
III. If you can do valve in our brand?
Yes,we can do your brand,but need you to provide the certificate of authrization for us.
IV. Where is your factory ?
Our factoury is located in Wenzhou city. If you have time ,welcome to visit us!
V.Which delivery port do you usually use?
There are three port we usually use:Shanghai pot,Ningbo port.
VI,What kinds of certificates do you have?
We have ISO9001:2000 quality certificates,3A certificatesand ISO14001:2014, FDA
Packing: